Super dish setup instructions

If applicable, connect a second satellite dish to the DPP Assembling and Mounting the Dish Follow these instructions to assemble the satellite dish, mount it, and point it in the direction of the satellites. Note: If your skew angle is at the extreme ends of the scale greater than or less than 70 , insert nuts and bolts from the hardware pack into the additional skew holes. These additional skew holes provide greater stability to the dish at these extreme angles. See Figure 2. Installing the Receivers Use the steps below while referring to Figure 1.

From the Point Dish screen, run Check Switch. On all other Legacy models, select Test. When the Check Switch procedure finishes, you should see an Installation Summary screen similar to the ones shown below. Do not disturb the receiver during the process of downloading software. If exiting the Point Dish screen does not start the download process, turn off the receiver for at least 20 minutes on most receivers to allow the receiver to take a software download.

Run Check Switch again and confirm reception for all three satellites on all available satellite tuners. Your Installation Summary screen should be similar to the ones shown above in step 8. Some software on some models may identify the DPP This identification is OK. If installing an additional receiver, follow steps Welcome Sign In Register.

Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles.

Part 1. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Select a flat spot on or around your home.

Find a level place that is accessible if you need to clean off or adjust the satellite dish later. If you have space, the safest place for a satellite dish is on the ground. It will have plenty of room to point north or south, depending on where you live. Also, keep the dish away from falling snow or ice, such as from your roof or nearby trees. Try to find a spot close to them to make the wiring process easier.

If you mount the dish on the ground, you will need to dig a trench to run its cables to your home safely. Check for any obstructions blocking the dish's view of the sky.

Stand where you plan on installing the dish. Look up to the sky. If you see buildings, trees, or even clotheslines in the way, then find another spot. These obstacles stop the dish from receiving a clear signal, affecting your picture quality. The rod gives the dish more height without it needing to be on the roof. Satellite dish installers almost automatically go for the roof to guarantee the satellite isn't obstructed.

You may need to do this, too, if you can't find an exact spot elsewhere. If you're in the northern hemisphere, the dish needs to point south to receive a signal. If you're in the southern hemisphere, it needs to point north, so keep that in mind when looking for obstacles. Hold the dish's mount to your home and mark the screw positions. The dish's support is an L-shaped rod with a base plate that fastens to your home. Position the base plate flat against the wall or roof in the location you chose.

Look for a series of holes on the plate for bolts. Then, use a permanent marker to note the position of these holes on the roof. Don't try to anchor it to siding since it won't hold.

Calculate the size of the pilot holes needed to secure the mount. The holes' exact size and depth depend on the dish you're installing, so reference the components that came with the satellite. That number will tell you how wide the holes need to be. Create the pilot holes using a drill bit the same size as the mounting bolts. Use a masonry drill bit to break through stone and other rigid surfaces without damaging your drill.

The bit needs to create holes that are the perfect size for the bolts. Drill into the spots you marked earlier once you are ready. Make sure the holes you create are straight, so the mounting bolts fit properly. If they are too small, the bolts won't fit. Erring on the side of caution is better when drilling.

You can always widen a small hole. Place the mount's metal plugs into the holes you drilled. Your dish will come with a set of metal plugs that serve as wall anchors. One end of each plug will have a bolt hole in it.

Flip the plugs, so the openings face toward you rather than the wall. You need those openings to secure the mount. When you bolt the wall mount in place, the tails open up, making the plugs harder to remove. Superdish setup. Toggle sidebar.

JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser. Dimmy Thread Starter. Dec 23, 11 0. IF your standing behind a superdish and looking at the lnbs from left to right. THe first two lnbs are in a casing. THe third one which is a dish plus pro is out by itself. Which lnb is which sat. How do I know if I have a or superdish.

The real problem I am having is I get signal but its on the wrong sat. Van SatelliteGuys Master. Jul 8, 9, 1 Virginia Beach. If the lnbf that is outside of the casing is on the right asuming your behind the dish, and this is a dish pro dual not a plus then you have a superdish.

The middle lnbf is the and the left lnbf is the fss stacked or lnbf, on the superdish the out side dish pro dual is the , the middle dish pro dual is the , and the is dead nuts center and is another fss stacked lnbf. That is correct, the superdish has only one external outside of the shroud lnbf and it is a dish pro dual or singal depending on how old it is. If your receiving signal from the wrong sat then its probable that your dish has moved out of alignment, this happens when the dish moves on its horizontal axis or its elevation falls or raises.

If it has moved on the horizontal then that means the sleeve bolts arent tight enough and the wind or another hazzard has turned it. If the elevation has changed its due either to a bad mount location that isnt sturdy and the dish's weight is pulling it down or the ground if its on a pole is soft or the pole wasnt cemented in, wasnt deep enough, or your in a hurricane location. Take a magnetic carpenters level, the small type and place it on the side of the pole if its on a pole and check for level on all sides.

If you take the casing off, just the top half, you will see 2 lnbfs without their own casing's, one will say dbs stacked, and the other will say fss stacked. Things to do I just started to install Dish network for my business and truthfully its been nothing but problems.

First off Dish does not give you enough money fo installation. With two guys to install a superdish it takes longer than two hours. Plus having two guys there it is actually 4 hours. This is non stop working hard not to metion in the freezing WI weather. This install seems pretty straight forward. Mount the dish run three rg6 coax to the multi switch and then run the wries to each box. A receiver connected to a multi-switch sends a switching signal back up the coax cable to enable the switch to select the correct LNB it needs to look at.

In the case of multiple 'dual LNBs', the process is the same except that now, each of the LNBs will be looking at a different satellite.

If you don't remember when your dish was installed or if you're just not sure that it is a 5-LNB, take a look at your dish and see if it matches either one of the DirecTV satellite dish. If not, you will have to order a new dish. With the slightly smaller inch, you can only pick either one of these satellite slots. To receive all available DISH Network channels, including all high definition local and national channels from a single satellite dish, you need an MPEG-4 compatible dish antenna.

Note: Deciding on the required number of LNBs, shape and size of your satellite dish, depends on a number of factors, including the area where you live, service provider, and programming package selected. This is something that is best decided after you speak with your digital satellite TV service provider.

Dish Installation Process Now that you have made the plunge and purchased a satellite dish, you need to get that satellite TV antenna up so you can receive all the channels!

The relatively small size of present day digital satellite TV dish antenna systems means that these may be practically fixed just about anywhere. In particular, these compact satellite dishes are especially suitable for city dwellers. While you may choose to have your new satellite dish installed by a professional, yet the actual installation process is not difficult to do.

The only real difficulty that may arise in the process is when aiming the dish to get the best signal from the satellites. This is a crucial step and it is this step which may warrant professional assistance. Remember that the satellite dish is your main link to those satellites floating around in space, so it has to be aimed properly to pick up the signals.

Some self-installation kits may be of assistance in this respect. Selecting the best location for your Satellite Dish First, you have to decide on the exact location where best to install your satellite dish. There are a few issues that you need to take into account here. Considerations shall include: Remember that DSS satellites are in a geo-stationary orbit above the equator.

Therefore, a satellite dish must point due South when your position is located north of the equator and North if you are located south of the equator. Choose a location that is easily accessible in case you need to clean snow or debris out of your satellite dish, or to re-adjust the dish in case it has lost its alignment.

A suitable location is to attach the dish to a post which has been sunken in the ground. The chosen location should be unobstructed by trees, branches, buildings, telephone lines, clotheslines, electrical wires, power lines, radio and television towers, etc. All are possible sources of interference.

In other words, there must be no obstructions between the dish site and the satellites in the sky. Once you determines that the location is suitable, you will have to decide on a permanent or portable installation. Unless you fell you will be relocating in the near future or you are living on rental property, a permanent installation in concrete is the better way to go.

In addition, make sure that the growth of new foliage does not impede your system. Ideally, the selected location should be such as to allow you to take a route that is as straight and as close to your television set as possible.

Finally, refer to the included instructions for any specific details. Choose a method of installation that allows your system to withstand the elements year-round and still remain perfectly aligned and rigidly mounted.

Remember that system movement can reduce signal reception to the point of complete loss. Always do a trial run on the ground for coax cable installation from the satellite dish to the place where it will enter your house. Make sure it is long enough to reach both points. Attach the cable to the satellite dish and then run it across your yard and into the house through a drilled hole. Once you have the dish mounted with the LNB attached at feedhorn and all cables LNB and Polarotor connected, I recommend that you place the receiver and a portable TV set near the dish for that you see a picture while make the adjusts.

Attach the cable to your television set. Seal all outdoor electrical connections with weatherproof sealant, and bury the incoming receiving line below the frost line level.